Regulatory/Compliance
Compliance with the many applicable local, state, and federal regulations is often a complex matter. Information or guidance offered by ACMA should never be used as a substitute for experienced regulatory expertise or legal counsel. ACMA staff can recommend consultants and attorneys for members needing assistance in specific regulatory areas.
ACMA's Government Affairs Department provides extensive information and guidance to help our members efficiently comply with applicable regulations, standards, and codes, as well as to effectively participate in the development of legislation and regulations at the national, state, and local levels.
ACMA's Government Affairs programs are made possible through the support of ACMA member companies, and most of our products and services are available only to members.
Note to suppliers and consultants: Please do not share ACMA's products with your nonmember customers or clients; instead, tell them to join ACMA.
Note to regulators: For your own personal reference, ACMA will provide complementary access to our Government Affairs products; please contact John Schweitzer at ACMA.
 denotes content for Member's Only.
Unified Emission Factors
MACT Standards
Styrene Communications and Stewardship
ACMA Advocacy Programs
- Dec. 1, 2008 - ACMA discussion paper on EPA's Oct. 7, 2008 CTGs for coatings and boatbuilding
- Nov 13, 2008 - ACMA comments to Ohio EPA on RACT for RPC operations and coatings
- Sept. 3, 2008 - Comments to EPA on the proposed CTG for boatbuilding, plastic parts coating, and adhesives
- August 1, 2008 - Comments on TCEQ permitting policy
- April 23, 2008 - ACMA comments to Indiana Dept Envi Mgmt on BACT requirements
- April 15, 2008 - Data summary submitted to EPA for filled-DCPD emission factors
- Feb. 6, 2008 - Comments to TCEQ on the Styrene ESL
- Jan. 15 2008 Supplement to the Oct. 8 2007 comments on EPA's draft guidance on non-atomized application of resin and gelcoat
- March 9, 2006 petition to EPA on filled resins
- March 16, 2006 petition to EPA on pultrusion averaging
- ACMA Oct. 17, 2007 comments on EPA's proposed Subpart 6-H rule on spray painting at area sources
- ACMA Oct. 8, 2007 comments on EPA's draft guidance on MACT and non-atomized
- ACMA June 29, 2007 comments to EPA on the Feb. 2007 Emission Factor Uncertainty Assessment Review Draft
- ACMA May 29, 2007 Comments on the proposed TCEQ Standard Permit
- ACMA May 29, 2007 Comments on the TCEQ Styrene Effects Screening Level
- ACMA March 21, 2007 comments to EPA on the NESHAP General Provisions (once-in-always-in)
- OSHA Fire Safety Standard
- HR3255 - Legislation to reform the OSHA fire safety rules for open molding
- ACMA Dec. 7, 2006 letter to the TCEQ on the proposed Texas Standard Permit
- ACMA Dec. 7, 2006 petition to Ohio EPA to establish a RACT for composites manufacturing
- ACMA Oct. 2, 2006 Comments on OH Rule 3745-21-07
- ACMA June, 2006 Comments on the OMB Risk Bulletin
- ACMA March 31, 2006 Comments to Cal-DOSH on PELs advisory committee process
- ACMA March 29, 2006 Comments to SCAQMD on PAR 1132
- ACMA March 9, 2006 letter to EPA on styrene and IRIS
- ACMA Jan. 2006 letter to SBA on IRIS reform
- ACMA Jan. 2006 letter to EPA on IRIS reform
- ACMA Dec. 2005 comments to OMB on the draft circular on agency guidance documents
- ACMA response to 2005 SCAQMD gel coat emissions test (including AQMD report)
ACMA PAC
Learn how you can become involved in ACMA PAC
Reference Materials
Emissions to the Air From Composites Operations
State and Local Regulation of Composites Manufacturing
OSHA and Other Worker Health/Safety
Hazardous Materials and Waste
Codes and Standards for Composites Manufacturing
Product Safety and Related
More Information
|
